Configuring Juniper SSG Firewalls to failover between Internet connections

I have been working with the Netscreen, and then Juniper firewall products for the past five years and am still learning new and interesting features they offer. One thing that I have been configuring more and more recently are secondary Internet connections and fail-over between them for clients. This post runs through the steps required to configure an SSG firewall to use track-IP to monitor IP addresses on the Internet and then automatically fail-over and fail-back an Internet connection.

The first thing we need to do is move the interfaces that will contain the Internet connections so each is in their own virtual router. This will allow us to have an active default route for each connection and they can behave independently of each other.

For this example I am using the 192.0.2.0/24 address range for my WAN connections – this was defined by the IETF as a subnet to be used for testing and documentation in RFC 5735. As these interfaces are both public facing I am also going to restrict the management to secure protocols only

Now we need to setup the default routes out of each virtual router so that each connection can communicate with the rest of the Internet

We need to ensure that our internal users are able to route to both the untrust-vr and adsl-vr. This can be done by exporting the default static route from the untrust-vr and adsl-vr

This will import both default routes to the trust-vr and set maintain the preference of the export from the untrust-vr at 20 whilst setting the metric of the adsl-vr export to 140.

Now that our users can connect to the Internet we need to make sure that should there be an issue with the primary internet circuit the backup circuit can be used for Internet access. This is achieved by using track-ip to monitor a number of hosts on the Internet and should they become unreachable shut the interface down.

In this example we are using the IP address of some of the root DNS servers as the addresses the firewall will use to check for a valid Internet connection but they could be any IP addresses that you expect to remain online and will respond to PING requests

This will PING the three addresses every second and will consider the address to have failed when the test has failed 25 times consecutively. Summing these three failures together will hit the weight and threshold limits of 75 needed to shut down the interface.

UPDATE: Since this was written Juniper released newer firmware that allowed you to specify the interface threshold for failure in addition to the Track-IP threshold. This would mean that track-ip would fail at 75 but the interface default was set to 255 for failover, the config above has been amended accordingly to reflect this change in behaviour.

If you want to test the status of the track-ip monitoring you can issue the following commands

and you will be able to see the failure statistics as well as whether the interface is failed or not.

When the interface is shut down the default route no longer becomes valid in the untrust-vr and will be deleted in the trust-vr leaving the export from the adsl-vr active and Internet traffic will continue to function as normal. In the background, the management address on the primary connection will continue to poll the IP addresses configured and when they become available the weight and threshold will be below the failure values, the interface comes back up and the untrust-vr route export re-appaers in the trust-vr.

The only other thing to consider here is inbound services on the backup line such as MX records to permit mail delivery to a MIP or VIP on the secondary circuit

If this is all configured correctly the only things the user should notice is that any websites/services that login and use session data (eg online banking) will need to login after fail-over or fail-back as their existing session will no longer be valid.

The only remaining task is to commit the changes you have made to flash

 

Multiple Juniper SSG clusters on same network

I ran into an issue recently with a client where we were seeing a large level of packet loss to their newly installed SSG140 cluster. There were three clients sharing the same 100Mbit Internet circuit and they all connected directly into a pair of Juniper SRX210 routers.

All three clients had a firewall cluster which was either made up of a pair of Juniper SSG 140s or Juniper SSG 5s and we were seeing the packet loss on the two SSG 140 clusters.

After some investigation and troubleshooting the following KB article from the Juniper website seemed to demonstrate what the problem was: http://kb.juniper.net/InfoCenter/index?page=content&id=KB7435

The virtual MAC address for both firewall clusters public facing interfaces were the same.

Resolution? Rebuild one of the clusters to use a different cluster ID and the MAC address generated for the firewalls is different.